Apr 06, 2022 השאר הודעה

ציוד אלקטרופורזה בפרופיל אלומיניום ופרמטרים טכניים

עקרון האלקטרופורזה

Electrophoresis is basically the same as traditional light and transparent electrophoresis. Anodic electrophoresis is performed under the action of direct current. Under the action of the electric field, the coated particles with charge move to the coated workpiece, so that the electrophoretic coating deposited on the surface of the aluminum profile precipitates, forming a film. The difference is in the type of coating and slightly different equipment.

Electrophoretic coatings include acrylic resins, melamine resins, pigments, solvents, neutralizers, additives and other ingredients. By thermal fixation in the viaduct layer of particles, the shape of the concave coating is essentially unchanged during baking and the appearance of the film is uniformly formed. Dimming can be adjusted by the ratio of high gloss paint to low gloss paint.

לציפוי אלקטרופורטי יש את המאפיינים הבאים בהשוואה לשיטות ציפוי אחרות:

(1) השימוש בציפוי מסיס במים-, מים כתווך התמיסה, חוסכים הרבה ממסים אורגניים, מפחיתים מאוד את זיהום האוויר ומפגעי הסביבה, בטיחות ובריאות, ומנעים את הסכנה הנסתרת של שריפה;

(2) יעילות ציפוי גבוהה, אובדן הציפוי קטן, שיעור הניצול של הציפוי יכול להגיע ל-90 אחוז 95 אחוז;

(3) עובי סרט אחיד, הידבקות חזקה, איכות ציפוי טובה, כל חלקי חומר העבודה כגון השכבה הפנימית, צניחת, ריתוך ומקומות אחרים יכולים להיות סרט אחיד וחלק, לפתור את בעיית הציפוי של שיטות ציפוי אחרות לחומר עבודה בעל צורה מורכבת ;

(4) יעילות ייצור גבוהה, בנייה יכולה לממש ייצור רציף אוטומטי, לשפר מאוד את יעילות העבודה;

(5) הציוד מורכב, עלות ההשקעה גבוהה, צריכת החשמל גדולה, טמפרטורת הייבוש והריפוי גבוהה, ניהול הציפוי והציפוי מורכב, תנאי הבנייה קפדניים ויש צורך בטיפול בשפכים;

(6) ניתן להשתמש רק בצבע מסיס במים-, ולא ניתן לשנות את הצבע בתהליך הצביעה. לא קל לשלוט ביציבות הצבע אם הוא נשמר לאורך זמן.

האחד, ציוד ציפוי אלקטרופורזה

ציוד ציפוי אלקטרופורטי מורכב ממיכל אלקטרופורזה, מכשיר ערבוב, מכשיר מסנן ציפוי, מכשיר ויסות טמפרטורה, מכשיר ניהול ציפוי, מכשיר אספקת חשמל DC, מכשיר כביסה לאחר ציפוי אלקטרופורטי, מכשיר סינון אולטרה, מכשיר אפייה, מיכל רזרבי וכן הלאה.

The size and shape of the electrophoresis tank should be determined according to the size, shape and construction process of the workpiece. Under the condition of ensuring a certain distance between poles, it should be designed as small as possible. The tank is equipped with a filter device and a temperature regulating device to ensure a certain temperature of the paint and remove impurities and bubbles in the circulating paint. The stirring device can make the working paint keep uniform and consistent, and the circulating pump is mostly used. The circulation of paint is generally 4-6 times per hour. When the circulating pump starts, the surface of the paint in the tank should be turned evenly. The function of the coating management device is to supplement and adjust the coating composition, control the PH value of the tank liquid, remove the neutralizer with diaphragm electrode and eliminate the low molecular weight components with ultrafiltration device. Dc power supply is generally used for selection of electrophoresis power supply. Rectifier equipment can be silicon rectifier or silicon controlled.

שניים, פרמטרי התהליך העיקריים המשפיעים על ציפוי אלקטרופורטי

1, המתח

Electrophoretic coating is a constant voltage method, the equipment is relatively simple, easy to control. Voltage has great influence on paint film; The higher the voltage is, the thicker the electrophoretic paint film is, and the coating ability can be improved accordingly for the parts that are difficult to be coated and the construction time can be shortened. But voltage is too high, can cause paint film surface coarse, easy generation after drying "orange peel" phenomenon. Low voltage, slow electrolytic reaction, thin and uniform paint film, poor penetration force. The choice of voltage is determined by coating type and construction requirement. Under normal circumstances, voltage and coating solid cent and paint temperature into inverse ratio, proportional to the distance between the two poles. Steel surface is 40 70V, aluminum and aluminum alloy surface can use 60 100V, galvanized parts use 70 85V.

2. זמן אלקטרופורזה

The film thickness increases with the extension of electrophoresis time, but when the film reaches a certain thickness, it can not increase the thickness, but will aggravate the side reaction. On the contrary, the electrophoresis time is too short, the coating is too thin. The electrophoresis time should be as short as possible according to the voltage used to ensure the quality of the coating. General workpiece electrophoresis time is 1 to 3 minutes, large workpiece 3 to 4 minutes. If the surface geometry of the coated object is complex, the voltage can be appropriately increased and the time can be prolonged.

3, טמפרטורת ציפוי

Coating temperature is high, film forming rate is fast, but the paint film appearance is rough, will also cause coating deterioration; Low temperature, less electrodeposition, slow film formation, thin and dense film. In the process of construction, due to electrical deposition part of the electrical energy into heat energy, mechanical friction in the circulation system to generate heat, will lead to coating temperature rise. General paint temperature control in some aspects 15 30 degree .

4, צבע נקודות מוצקות ויחס בסיס יאן

The solid cent of the electrophoretic coating that sells on the market is generally about 50 percent , when construction, need to use distilled water to control the coating solid cent in 10 percent 15 percent . The solid content is too low, the covering power of the paint film is not good, the pigment is easy to precipitate, and the stability of the paint is poor. Solid points too high, viscosity, will cause the paint film rough loose, poor adhesion. The face base ratio of high gloss electrophoretic coating can be controlled at 1 to 4. As a result of actual operation in, the pigment quantity of coating can drop gradually, must add pigment to cent tall coating to adjust at any time.

5, ערך ה-PH של הציפוי

The PH value of electrophoretic coating directly affects the stability of bath. If PH value is too high, the newly deposited film will dissolve again, the film will become thin, and the film will be removed after washing after electrophoresis. PH value is too low, the workpiece surface gloss is inconsistent, the stability of the paint is not good, the dissolved resin will be precipitated, the paint film surface is rough, adhesion is reduced. Generally, the PH value should be between 7.5 and 8.5 during construction. During construction, cationic ammonium compounds accumulated in the paint due to continuous electrophoresis, resulting in an increase in PH value. The solution with low PH value can be added, the distilled water of the cathode cover can be replaced, ammonium ion can be removed by ion exchange resin, and the PH value can be reduced by anodic cover. If the PH value is too low, can be added to adjust the ammonium ethanol.

6. עמידות לציפוי

The impurities ions brought into the electrophoretic tank by the previous process of the coated objects cause the decrease of resistance value of the paint, resulting in uneven roughness and pinholes and other defects of the paint film. In painting construction, the coating should be purified. In order to obtain high quality coating, cathode cover equipment can be used to remove positive ions such as ammonium and calcium and magnesium impurities.

7. מרחק בין חומר העבודה לקתודה

Short distance, high deposition efficiency. But the distance is too close, can make paint film is too thick and generation flow hangs, orange skin to wait for malady. Generally, the distance is not less than 20cm. For large and complex shape of the workpiece, when the external has been deposited very thick film, and the internal film is still thin, should be far from the cathode part, increase the auxiliary cathode.

שיטות ומיומנויות של ציור אלקטרופורטי

(1) ציפוי אלקטרופורטי של משטח מתכת, התהליך הטכנולוגי שלו הוא כדלקמן:

Pre-cleaning → on-line → degreasing → washing → rust removal → washing → neutralization → washing → phosphating → washing → passivation → electrophoretic painting → in-tank cleaning → ultrafiltration washing → drying → offline.

(2) The substrate and pretreatment of the coating have a great influence on the electrophoretic coating film. Castings generally use sandblasting or shot blasting for rust removal, with cotton yarn to remove floating dust on the surface of the workpiece, with 80 120 sand paper to remove residual steel shot and other sundries on the surface. The surface of steel is treated with oil removal and rust removal. When the surface requirements are too high, phosphating and passivation surface treatment can be carried out. Ferrous metal workpiece must be phosphating before anodic electrophoresis, otherwise the corrosion resistance of the paint film is poor. Phosphating treatment, generally choose zinc salt phosphating film, thickness of about 1 2μm, requires fine and uniform crystallization of phosphating film.

(3) The circulation quantity of electrophoretic coating system directly affects the stability of bath liquid and the quality of paint film. With the increase of circulation, the precipitation and bubble in the tank decrease. However, the aging of the tank is accelerated, the energy consumption increases, and the stability of the tank becomes worse. It is ideal to control the circulation number of tank liquid 6 8 times /h, not only to ensure the quality of paint film, but also to ensure the stable operation of tank liquid.

(4) Ultrafiltration system controls the concentration of impurity ions brought into the workpiece to ensure the coating quality. In the operation of this system, attention should be paid to the continuous operation of the system after operation, discontinuous operation is strictly prohibited to prevent the drying of the ultrafiltration membrane. The dried resin and pigment adhere to the ultrafiltration membrane and cannot be thoroughly cleaned, which will seriously affect the permeability and service life of the ultrafiltration membrane. The effluent rate of ultrafiltration membrane decreases with the running time, and it should be cleaned once for 30 to 40 days in order to ensure the ultrafiltration water required for leaching and washing.

4. ביצועי מוצר מעולים

(1) שקיפות גבוהה וגודל מלא, עם ברק ושקיפות מיוחדים, הציפוי בעל אפקט תלת מימדי- גבוה, וצבע המצע ברור.

(2) קשיות גבוהה, כאשר אופים ב-180 מעלות למשך 30 דקות, הקשיות יכולה להגיע ל-4 עד 5 שעות.

(3) נזילות טובה, סרט יציב וסרט חלק.

(4) כוח קשירה וחדירות חזק, ציפוי נמצא בכל מקום, לסרט רטוב ולסרט יבש יש כוח קשירה חזק.

(5) ביצועים טובים, חומר העבודה אינו משנה צבע בטמפרטורת אפייה של 180 מעלות 200 מעלות, מתנגד לשינוי צבע וקורוזיה, צבע המוצר והברק בהיר ומתמשך, אפקט הקורוזיה הוא אידיאלי.

(6) האפקט האלקטרופורטי הממוצע טוב, סרט הצבע אחיד וחלק, ב-90-200V יכול להגיע ל-10-16um, יעילות גבוהה, צריכת חשמל נמוכה.

(7) עמידות טובה בפני השפעה ועמידות בזיעה מלאכותית.

(8) זה יכול לשמש עבור אלומיניום, ציפוי מתכת, אביזרי מתכת יקרים, מנורות והגנה על פני רהיטים-מתקדמים.

(9) It can be electrophoretic into a variety of color paste: titanium, ordinary gray, pure black and other colors. Because of the high screening rate of matte electrophoretic coating film, the extrusion die pattern on the surface of aluminum has a certain hiding effect, and also has a certain compensation effect on the color difference of dyeing process.

חמש, המאפיינים העיקריים של אלומיניום אלקטרופורטי-בדרגה גבוהה:

1, עם קשיות סרט חזקה, עמידות בפני השפעה חזקה.

2, עם סרט הדבקה גבוה, לא קל ליפול מההזדקנות.

3. יש לו עמידות בפני שחיקה, עמידות בפני מזג אוויר ועמידות בפני אלקלי טובה יותר מאשר תחמוצת אלומיניום.

4, צבע פני השטח עשיר, יפה, עם אפקט ברק במראה-.

שש, העיקרון והיישום של צבע הכחדה

With the development of electrophoretic coating technology, in China's coating industry, it has become the world's top coating manufacturers, formed relevant industrial groups, and actively promote the technological revolution and development of traditional coating field. During this period, bright and bright paint with its bright colors and bright colors and welcomed by consumers, and in a long period of time by the paint market. However, with the improvement of people's living standard, on the one hand, consumers feel that high gloss coating is more serious than reflective coating, which is harmful to people's eyes. On the other hand, consumers have an increasingly casual, fashionable and personalized aesthetic concept. Coupled with the booming demand of China's electronics and electrical industry. These factors have led to a sharp increase in the demand for low-gloss coatings with a soft appearance. At the same time, how to produce matte coatings must be considered.

שבעה, גורמי ברק

Light projected onto the surface of the object will reflect light, and the surface of the object will reflect in light. Different surfaces have different glossiness. Measuring the surface size of light reflected by light is called glossiness. Glossiness is expressed as a percentage. The higher the glossiness of a surface, the greater its ability to reflect light and its brightness. Glossiness is measured by a photoelectric gloss meter. According to the size of gloss, coatings can be divided into light, matte and weak light. Coating gloss classification (60 reflections) :

(1) אור נמוך: ברק פחות מ-10 אחוזים;

(2) מאט: מבריק 10 60 אחוז;

(3) light: gloss GT; 60 percent .

שמונה, השפעת גורמי ברק

Surface gloss of an object is closely related to surface roughness. When light is on the surface of an object, some of it is absorbed by the object, some is reflected and scattered, and some is refracted. The smaller the surface roughness, the more light reflected and the higher the gloss. Conversely, if the surface of the object is not flat, the scattered light increases, causing the luster to decrease. The surface roughness (H) of the polished object can be perceived by human vision, and the theoretical knowledge of the microscopic surface can be calculated according to the following formula: H = λ/ cos a, where λ is the wavelength of incident light; One is the incident Angle. If the incident Angle is 60 degree , h =1.1μm is calculated. When the surface roughness is greater than 1.1μm, it will show uneven and glossiness decreases.


שלח החקירה

whatsapp

טלפון

דוא

חקירה